This adapter lets you use PS1 and PS2 controllers on your PC. The multitap is also supported, enabling simultaneous use of up to 3 controllers. Memory cards connected to a multitap can also be read and written to, making it possible to backup, share or transfer your games to emulators. For data use pin 2 of the ps/2 and connect that to pin 2 on the usb. For clock use pin 6 of the ps/2 and connect that to pin 3 on the usb. Proper ps/2 connectors are colour coded, e.g. Purple is keyboard and green is mouse this is reflected on the sockets on the back of the computer to make sure the correctly wired plug is installed. Very useful USB driver for Windows 98 based computer. Ratnendra Ashok Posts 601 Registration date Wednesday November 28, 2018 Status Member Last seen. Older board for use when a PS/2 keyboard connection on the host is the only available (ie no USB available).

About Vilros Retro Gaming USB Classic Controller Sets

Will update this. Posting for now.

Initial setup:

SSH into retropie

cd /opt/retropie/configs/all/retroarch-joypads

With your controller, enter emulationstation. Let the controller connect, be detected, and create the initial config as described in each section relevant to the controller. Once finished, at the SSH commandline, run:

ls
NOTE: the VILROS NES controller, the SNES controller, and the 6-button controller all have the same USB ID number & name. When plugging the controller in and configuring in emulationstation, a .cfg file will be created in /opt/retropie/configs/all/retroarch-joypads. In this case, when plugging the NES controller, this file is created:
'USB Gamepad .cfg'

Copy this file to <systemname - USBname.cfg>

This example: cp 'USB Gamepad .cfg' NES-controller-USB-Gamepad.cfg

When swapping controllers, copy the file back:

cp /opt/retropie/configs/all/retroarch-joypads/NES-controller-USB-Gamepad.cfg /opt/retropie/configs/all/retroarch-joypads/'USB Gamepad .cfg'

Do the initial setups for each emulator/controller combination. Once the controller is active in emulationstation, the buttons will need mapped to the cores. Tf2 sniper tips. This is detailed in each section below. You should have 3 files created:

NES-controller-USB-Gamepad.cfg
Sega-6button-USB-Gamepad.cfg
SNES-controller-USB-Gamepad.cfg

Restart emulationstation from within the ES interface or restart the retropie from the terminal with sudo reboot. The controller will be ready for use for each of the game systems it has been configured for.

Creating controller-specific mapping:

After configuring each controller as shown below, the configurations for these mapppings should be move from defaults to controller-specific names to make loading the configurations simpler.

SSH to the retropie:
cd /opt/retropie/configs/nes/<emulator>/
cp <emulator>.rmp <controller-emulator>.rmp
rm <emulator.rmp>

Example:

pi@superpi:/opt/retropie/configs/snes/Snes9x $ cd /opt/retropie/configs/nes/Snes9x/
pi@superpi:/opt/retropie/configs/snes/Snes9x $ cp Snes9x.rmp SNES-Snes9x.rmp
pi@superpi:/opt/retropie/configs/snes/Snes9x $ rm Snes9x.rmp

NES Classic Controller

= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Initial setup specific to NES & Vilros NES Controller
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =

• plug in keyboard & controller
• Configure in emulationstation – allow hotkey to be ‘select’ (button 8)
• Detects as ‘USB Gamepad .cfg’
• edit /opt/retropie/configs/nes/retroarch.cfg
• add input_menu_toggle_btn = '1' above #include
• restart emulationstation
• open NES game
• open RGUI with ‘select + a button’
• Controls -> Port 1 Controls
• change ‘A button 1’ to ‘A’
• change ‘X button 2’ to ‘B’
• press ‘z’ on the keyboard
• Save Core Remap File
• Load Remap File -> <emulator-name>.rmp

= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Initial setup specific to Sega Game Gear & Vilros NES Controller
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =

• plug in keyboard
• Configure in emulationstation – allow hotkey to be ‘select’ (button 8)
• Detects as ‘USB Gamepad .cfg’
• edit /opt/retropie/configs/gamegear/retroarch.cfg
• add ‘input_menu_toggle_btn = “1”‘ above #include
• restart emulationstation
• open Game Gear game
• open RGUI with ‘select + a button’
• Controls -> Port 1 Controls
• change ‘A button 1’ to ‘C’
• change ‘X button 2’ to ‘B’
• press ‘z’ on the keyboard
• Save Core Remap File
• Load Remap File -> .rmp

= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Initial setup specific to Gameboy/Gameboy Color & Vilros NES Controller
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =

• plug in keyboard
• Configure in emulationstation – allow hotkey to be ‘select’ (button 8)
• Detects as ‘USB Gamepad .cfg’
• edit /opt/retropie/configs/gb or gbc/retroarch.cfg
• add ‘input_menu_toggle_btn = “1”‘ above #include
• restart emulationstation
• open Gameboy game
• open RGUI with ‘select + a button’
• Controls -> Port 1 Controls
• change ‘A button 1’ to ‘A’
• change ‘X button 2’ to ‘B’
• press ‘z’ on the keyboard
• Save Core Remap File
• Load Remap File -> .rmp

= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Initial setup specific to Sega Master System & Vilros NES Controller
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =

• plug in keyboard
• Configure in emulationstation – allow hotkey to be ‘select’ (button 8)
• Detects as ‘USB Gamepad .cfg’
• edit /opt/retropie/configs/ngp/retroarch.cfg
• add ‘input_menu_toggle_btn = “1”‘ above #include
• restart emulationstation
• open Master System game
• open RGUI with ‘select + a button’
• Controls -> Port 1 Controls
• change ‘A button 1’ to ‘Button 2’
• change ‘X button 2’ to ‘Button 1 Start’
• press ‘z’ on the keyboard
• Save Core Remap File
• Load Remap File -> .rmp

= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Initial setup specific to NEOGEO Pocket & Vilros NES Controller
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =

• plug in keyboard
• Configure in emulationstation – allow hotkey to be ‘select’ (button 8)
• Detects as ‘USB Gamepad .cfg’
• edit /opt/retropie/configs/ngpc/retroarch.cfg
• add ‘input_menu_toggle_btn = “1”‘ above #include
• restart emulationstation
• open a NEOGEO Pocket game
• open RGUI with ‘select + a button’
• Controls -> Port 1 Controls
• change ‘A button 1’ to ‘A’
• change ‘X button 2’ to ‘B’
• press ‘z’ on the keyboard
• Save Core Remap File
• Load Remap File -> .rmp

= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Initial setup specific to PC Engine/TurboGraphix 16 & Vilros NES Controller
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =

• plug in keyboard
• Configure in emulationstation – allow hotkey to be ‘select’ (button 8)
• Detects as ‘USB Gamepad .cfg’
• edit /opt/retropie/configs/pcengine/retroarch.cfg
• add ‘input_menu_toggle_btn = “1”‘ above #include
• restart emulationstation
• open a PC Engine/TurboGraphix 16 game
• open RGUI with ‘select + a button’
• Controls -> Port 1 Controls
• change ‘A button 1’ to ‘I’
• change ‘X button 2’ to ‘II’
• press ‘z’ on the keyboard
• Save Core Remap File
• Load Remap File -> .rmp

= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Initial setup specific to Atari 2600 & Vilros NES Controller
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =

• plug in keyboard
• Configure in emulationstation – allow hotkey to be ‘select’ (button 8)
• Detects as ‘USB Gamepad .cfg’
• edit /opt/retropie/configs/atari2600/retroarch.cfg
• add ‘input_menu_toggle_btn = “1”‘ above #include
• restart emulationstation
• open a Atari 2600 game
• open RGUI with ‘select + a button’
• Controls -> Port 1 Controls
• change ‘A button 1’ to ‘—‘
• change ‘X button 2’ to ‘Fire’ – Sets the B button to usable
• press ‘z’ on the keyboard
• Save Core Remap File
• Load Remap File -> .rmp

Super Nintendo Entertainment System (SNES) Controller

= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Initial setup specific to Super Nintendo & Vilros SNES Controller
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Tested using Super Mario World [US]

• Configure in emulationstation – allow hotkey to be ‘select’ (button 8)
• Detects as ‘USB Gamepad .cfg’
• restart emulationstation
• open SNES game
• open RGUI with ‘select + left bumper’
• Controls -> Port 1 Controls
• change ‘B button 0’ to ‘A’
• change ‘Y button 3’ to ‘Y’
• change ‘A button 1’ to ‘X’
• change ‘X button 2’ to ‘B’
• Save Core Remap File
• Load Remap File -> snes9x.rmp

Sega 6-button Controller

= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Initial setup specific to Sega Megadrive & Vilros 6-button Controller
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =

(tested using lr-genesis-plus-gx)
Used Section 4b as my button guidance – https://gamefaqs.gamespot.com/genesis/586509-super-street-fighter-ii/faqs/63633

• Configure in emulationstation – allow hotkey to be ‘select’ (button 8)
• Detects as ‘USB Gamepad .cfg’
• edit /opt/retropie/configs/megadrive/retroarch.cfg
• Add these next two lines above #include:
• input_libretro_device_p1 = “513”
• input_libretro_device_p2 = “513”
• No need to set ‘input_menu_toggle_btn = “1”‘; this will be middle-top button (X)
• restart emulationstation
• open a Sega Megadrive game
• open RGUI with ‘select + a button’
• Controls -> Port 1 Controls
• change ‘B button 0’ to ‘A’
• change ‘Y button 3’ to ‘X’
• change ‘A button 1’ to ‘B’
• change ‘X button 2’ to ‘C’
• change ‘L Button 4’ to ‘Y’
• change ‘R Button 5’ to ‘Z’
• press ‘A’ on the controller (bottom left)
• Save Core Remap File
• Load Remap File -> .rmp

= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Initial setup specific to Sega CD & Vilros 6-button Controller
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =

These are the same instructions as the Sega Megadrive

• Configure in emulationstation – allow hotkey to be ‘select’ (button 8)
• Detects as ‘USB Gamepad .cfg’
• edit /opt/retropie/configs/segacd/retroarch.cfg
• Add these next two lines above #include:
• input_libretro_device_p1 = “513”
• input_libretro_device_p2 = “513”
• No need to set ‘input_menu_toggle_btn = “1”‘; this will be middle-top button (X)
• restart emulationstation
• open a Sega CD game
• open RGUI with ‘select + a button’
• Controls -> Port 1 Controls
• change ‘B button 0’ to ‘A’
• change ‘Y button 3’ to ‘X’
• change ‘A button 1’ to ‘B’
• change ‘X button 2’ to ‘C’
• change ‘L Button 4’ to ‘Y’
• change ‘R Button 5’ to ‘Z’
• press ‘A’ on the controller (bottom left)
• Save Core Remap File
• Load Remap File -> .rmp

= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Initial setup specific to Sega 32x & Vilros 6-button Controller
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =

(tested using picodrive)
https://retropie.org.uk/forum/topic/16801/can-t-get-6-button-controller-sega-emulators

• Configure in emulationstation – allow hotkey to be ‘select’ (button 8)
• Detects as ‘USB Gamepad .cfg’
• No need to set ‘input_menu_toggle_btn = “1”‘; this will be middle-top button (X)
• restart emulationstation
• open a Sega Megadrive game
• open RGUI with ‘select + a button’
• Go into Quick Menu -> Options and set player 1 (and 2) to 6-button controller
• Controls -> Port 1 Controls
• change ‘B button 0’ to ‘A’
• change ‘Y button 3’ to ‘X’
• change ‘A button 1’ to ‘B’
• change ‘X button 2’ to ‘C’
• change ‘L Button 4’ to ‘Y’
• change ‘R Button 5’ to ‘Z’
• press ‘A’ on the controller (bottom left)
• Save Core Remap File
• Load Remap File -> find the sega32x.rmp file.

= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Initial setup specific to Sega Saturn & Vilros 6-button Controller
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =

• Configure in emulationstation – allow hotkey to be ‘select’ (button 8)
• Detects as ‘USB Gamepad .cfg’
• No need to set ‘input_menu_toggle_btn = “1”‘; this will be middle-top button (X)
• restart emulationstation
• open a Saturn game
• open RGUI with ‘select + a button’
• Controls -> Port 1 Controls
• change ‘B button 0’ to ‘B’
• change ‘Y button 3’ to ‘X’
• change ‘Select button 8’ to ‘—‘
• change ‘A button 1’ to ‘A’
• change ‘X button 2’ to ‘C’
• change ‘L Button 4’ to ‘Y’
• change ‘R Button 5’ to ‘Z’
• press ‘A’ on the controller (bottom left)
• Save Core Remap File
• Load Remap File -> find the Yabause.rmp file.

= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Initial setup specific to Panasonic 3DO & Vilros 6-button Controller
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =

This was functionally useless – https://github.com/RetroPie/RetroPie-Setup/wiki/3do
Kontakt 6 full version. Tested this with DOOM to get the buttons correct.

• Configure in emulationstation – allow hotkey to be ‘select’ (button 8)
• Detects as ‘USB Gamepad .cfg’
• No need to set ‘input_menu_toggle_btn = “1”‘; this will be middle-top button (X)
• restart emulationstation
• open a 3DO game
• open RGUI with ‘select + a button’
• Controls -> Port 1 Controls
• change ‘B button 0’ to ‘A’
• change ‘Y button 3’ to ‘L’
• change ‘Select 8’ to ‘X (Stop)’
• change ‘A button 1’ to ‘B’
• change ‘X button 2’ to ‘C’
• change ‘L Button 4’ to ‘—‘
• change ‘R Button 5’ to ‘R’
• press ‘A’ on the controller (bottom left)
• Save Core Remap File
• Load Remap File -> find the Opera.rmp file.

Nintendo N64 Controller

= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Initial setup specific to Nintendo 64 & Vilros N64 Controller –
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =

4-17-20

• – Config is “good enough”, but still issues with GoldenEye I’m not sure how to resolve

using lr-mupen64plus:

Configuring initial setup from
https://github.com/RetroPie/RetroPie-Setup/wiki/Nintendo-64
Tested using F-Zero X with this as my guide: https://strategywiki.org/wiki/F-Zero_X/Controls
https://forum.recalbox.com/topic/3170/solved-n64-emulator-doesn-t-work-with-n64-usb-controller/2

• Controller detects as: DragonRise Inc. Generic USB Joystick .cfg
• Configure in emulationstation – do not set hotkey ‘select’
• edit /opt/retropie/configs/n64/retroarch.cfg
• add ‘input_menu_toggle_btn = “4”‘ above #include
• restart emulationstation
• open a N64 game
• open RGUI with ‘left bumper (button 4)’
• Controls -> Port 1 Controls
• – Analog to Digital Type to ‘None’
• – B Button 0 to ‘C1’
• – Y button 3 to ‘B Button (C2)’
• – Select Button 8 to ‘B Button (C2)’
• – A button 1 to ‘A Button (C3)’
• – X Button 2 to ‘C4’
• – L button 4 to ‘L-Trigger’
• – R button 5 to ‘R-Trigger’
• – L2 button 6 to ‘A Button (C3)’
• – R2 button 7 to ‘Z-trigger’
• press ‘^’ on the controller (Top C button)
• Save Core Remap File
• pres ‘>’ on controller (Right C button)
• Load Remap File -> find the file.
• ssh – cd /opt/retropie/configs/n64/
• cd
• cp .rmp .rmp

************| This is incomplete |****************
info for using mupen64plus (not done yet):

for /opt/retropie/configs/n64/InputAutoCfg.ini

[DragonRise Inc. Generic USB Joystick]
plugged = True
plugin = 2
mouse = False
AnalogDeadzone = 4096,4096
AnalogPeak = 32768,32768
DPad R = axis(5+)
DPad L = axis(5-)
DPad D = axis(6+)
DPad U = axis(6-)
Start = button(9)
Z Trig = button(7)
B Button = button(8)
A Button = button(6)
C Button R = button(1)
C Button L = button(3)
C Button D = button(2)
C Button U = button(0)
R Trig = button(5)
L Trig = button(4)
Mempak switch = key(109)
Rumblepak switch = key(114)
Y Axis = axis(1-,1+)
X Axis = axis(0-,0+)

Not Needed, but not deleting just yet:

input_menu_toggle_btn = “4”
input_select_btn = “7”

input_exit_emulator_btn = “-0”
input_reset_btn = “8”
input_menu_toggle_btn = “7”
input_select_btn = “4”

input_r_y_minus_btn = “0”
input_r_y_plus_btn = “2”
input_r_x_minus_btn = “3”
input_r_x_plus_btn = “1”
***********************************************

Sony Playstation Controller

= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Initial setup specific to Sony Playstation & Vilros PS2 Controller
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =

Tested with ‘Batman Beyond: Return of The Joker.’ – game has button-map in the startup options

• Turn the analog button. ‘Analog’ will glow red.
• Configure in emulationstation – allow hotkey to be ‘select’ (button 8)
• Detects as ‘Microntek USB Joystick .cfg’
• No need to set ‘input_menu_toggle_btn = “1”‘; this will be Triangle)
• open a PSX game
• open RGUI with ‘select + Triangle button’
• Controls -> Port 1 Controls
• change ‘B button 0’ to ‘Triangle’
• change ‘Y button 3’ to ‘Square’
• change ‘Select 8’ to ‘Select’
• change ‘A button 1’ to ‘Circle’
• change ‘X button 2’ to ‘Cross’
• change ‘L Button 4’ to ‘L1’
• change ‘R Button 5’ to ‘R1’
• press ‘Triangle’ to go back.
• Save Core Remap File
• Load Remap File -> find the .rmp file.

= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Initial setup specific to Sony PSP & Vilros PS2 Controller
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =

Using PPSSPP – Just worked. Ran through the tests from

Hit Esc on the keyboard and went through programming the buttons. They were already set correctly.
Had to set the L and R. These mapped to

L – pad1.b6
R – pad1.b5

All other buttons were correct.

= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Initial setup specific to Sega Dreamcast & Vilros PS2 Controller
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =

Using REDREAM – Just worked.

Hit Esc on the keyboard and went through programming the buttons. They were already set correctly.

Changed mapping of Select button to REDREAM Main Menu.

All other buttons were correct.

Usb Ps2 Controller Driver Downloadinaboxlasopa Windows 7

= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Controller USB IDs
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
Determined by plugging each in, then running dmesg

NES Controller:

[17931.436014] usb 1-1.4: new low-speed USB device number 8 using xhci_hcd
[17931.582235] usb 1-1.4: New USB device found, idVendor=0079, idProduct=0011, bcdDevice= 1.06
[17931.582247] usb 1-1.4: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[17931.582255] usb 1-1.4: Product: USB Gamepad
[17931.592100] input: USB Gamepad as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.4/1-1.4:1.0/0003:0079:0011.0005/input/input5
[17931.592444] dragonrise 0003:0079:0011.0005: input,hidraw2: USB HID v1.10 Joystick [USB Gamepad ] on usb-0000:01:00.0-1.4/input0

SNES Controller:

Usb Ps2 Controller Driver Downloadinaboxlasopa 64-bit

[18010.527102] usb 1-1.4: new low-speed USB device number 9 using xhci_hcd
[18010.673572] usb 1-1.4: New USB device found, idVendor=0079, idProduct=0011, bcdDevice= 1.06
[18010.673581] usb 1-1.4: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[18010.673587] usb 1-1.4: Product: USB Gamepad
[18010.685552] input: USB Gamepad as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.4/1-1.4:1.0/0003:0079:0011.0006/input/input6
[18010.685808] dragonrise 0003:0079:0011.0006: input,hidraw2: USB HID v1.10 Joystick [USB Gamepad ] on usb-0000:01:00.0-1.4/input0

Sega 6-button controller:

Usb Ps2 Controller Driver Downloadinaboxlasopa Win 7

[18178.759401] usb 1-1.4: new low-speed USB device number 10 using xhci_hcd
[18178.895751] usb 1-1.4: New USB device found, idVendor=0079, idProduct=0011, bcdDevice= 1.06
[18178.895761] usb 1-1.4: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[18178.895767] usb 1-1.4: Product: USB Gamepad
[18178.907599] input: USB Gamepad as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.4/1-1.4:1.0/0003:0079:0011.0007/input/input7
[18178.907918] dragonrise 0003:0079:0011.0007: input,hidraw2: USB HID v1.10 Joystick [USB Gamepad ] on usb-0000:01:00.0-1.4/input0

N64 Controller:
[ 10.123670] bcm2835-codec bcm2835-codec: Loaded V4L2 isp
[ 10.128000] input: DragonRise Inc. Generic USB Joystick as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.4/1-1.4:1.0/0003:0079:0006.0003/input/input3
[ 10.128766] dragonrise 0003:0079:0006.0003: input,hidraw2: USB HID v1.10 Joystick [DragonRise Inc. Generic USB Joystick ] on usb-0000:01:00.0-1.4/input0

Usb Ps2 Controller

PS2 Controller:
[15340.573573] usb 1-1.4: new low-speed USB device number 7 using xhci_hcd
[15340.712526] usb 1-1.4: New USB device found, idVendor=0079, idProduct=0006, bcdDevice= 1.07
[15340.712532] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[15340.712537] usb 1-1.4: Product: USB Joystick
[15340.712541] usb 1-1.4: Manufacturer: Microntek
[15340.724899] input: Microntek USB Joystick as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.4/1-1.4:1.0/0003:0079:0006.0004/input/input4
[15340.725117] dragonrise 0003:0079:0006.0004: input,hidraw2: USB HID v1.10 Joystick [Microntek USB Joystick ] on usb-0000:01:00.0-1.4/input0

Usb Adapter For Ps2 Controller